產品詳情
開料機（KLJ)
開料設備CUTTING EQUIPMENT
產品用途 PRODUCT USE
該設備用于將盤管開卷、校直、無屑切斷成為定尺直管;主要應用于空調、熱水器、飛機汽車等管路得下料要求。
This equipment is used for uncoiling, straightening and cutting the coil into straight pipe with fixed length; it is mainly used for the blanking requirements of air conditioning, water leater, aircraft and automobile pipelines
開料設備CUTTING EQUIPMENT
產品用途 PRODUCT USE
該設備用于將盤管開卷、校直、無屑切斷成為定尺直管;主要應用于空調、熱水器、飛機汽車等管路得下料要求。
This equipment is used for uncoiling, straightening and cutting the coil into straight pipe with fixed length; it is mainly used for the blanking requirements of air conditioning, water leater, aircraft and automobile pipelines
| 技術參數Technical beters | |||
| (MAX)加工管徑 | 可選配 13: φ13mm ¨ 20: φ20mm ¨ | ||
| Max pipe diamerer | |||
| 加工工位 | 可選配 1:單管 ¨ 2:雙管¨ 4:四管 ¨ 6:六管 ¨ | ||
| Processing station | 1:Single pipe 2:Two pipes 4:Four pipes 2+4：Double two pipes | ||
| 一次送料長度 | 可選配 500: 500mm ¨ 1000: 1000mm ¨ x: 連續送料 ¨ | ||
| One feeding length | X: Continuous feeding | ||
| 放料架 | 可選配 E:主動式 ¨ P:被動式 ¨ | ||
| Cradle | E:Subject-verb b P:Passive | ||
| 放料架可旋轉 | 可選配 1：單面 ¨ 2:雙面可旋轉 ¨ | ||
| Cradle can rotate | 1：Single-sided 2:Two sideds can rotate | ||
| 材質 | 盤型銅管TP1/2或相當標準產品 | ||
| Material | Disc type copper pipe TP1/2 or equivalentstandard products | ||
| 銅管外徑 | φ6.0-φ20 | ||
| Outer diameter of brass | |||
| 銅管壁厚 | 0.3mm-1.5mm | ||
| Brass wall thickness | |||
| 料盤外徑 | φ1000-φ1250 | ||
| Outer diameter of the tray | |||
| 料盤中心孔徑 | φ130 | ||
| The center aperture of the tray | |||
| 料盤間距 | 250-340 | ||
| Spacing of the trays | |||
| 盤管重量 | ≤280kg | ||
| Coil weight | |||
| 氣壓范圍 | 0.5-0.7MPa | ||
| Air pressure range | |||
| 使用電源 | 三相四線AC380V 50Hz | ||
| Power supply | (hree-phase four-wire) | ||
| 總功率 | 4.5KW | ||
| Totalpower | |||
| 直線度公差 | ≤20‰ | ||
| Straightness tolerance | |||
| 一次開料平齊度 | ≤0.5mm(L=1000) | ||
| material to open evenness | |||
| 表面狀況 | 銅管表面無明顯拉、劃、壓傷痕 | ||
| Surface condition | Brass surface without obvious pull, stroke, pressure scar | ||
| 管口內徑縮口率 | f<20%(實際壁-厚壁厚)/壁厚 | ||
| Orifice diameter | F& It: 20%(actual wall thickness- wall thickness)/ wall thickness | ||
| 銅管不圓度 | ≤3% | ||
| Copper pipe is not round | |||
| 生產效率 | 8次/分鐘(L=1000) | ||
| Productivity | 8 times/min (L=1000) | ||
購物須知：
因本店所有寶貝涉及加工訂制，詳情頁所描術技術參數是常規可滿足的，超出參數范圍可以進行非標訂制。具體詳情請聯系客服人員，我司將由技術部人員設計方案，再由工程部核算價格，確認好后方可付款。
地址：江蘇省蘇州市吳中區胥口鎮新峰路188號5棟
公司網址：www.szvedette.com
郵編：415105
電話：0512-66537128
傳真：0512-66537129
聯系人：馬女士
電話: 19852907234
郵箱：3583733793@qq.com
